Abstract  In a study screening anaerobic microbes utilizing D: -galactitol as a fermentable carbon source, four bacterial strains were isolated from an enrichment culture producing H₂, ethanol, butanol, acetic acid, butyric acid, and hexanoic acid. Among these isolates, strain BS-1 produced hexanoic acid as a major metabolic product of anaerobic fermentation with D: -galactitol. Strain BS-1 belonged to the genus Clostridium based on phylogenetic analysis using 16S rRNA gene sequences, and the most closely related strain was Clostridium sporosphaeroides DSM 1294(T), with 94.4% 16S rRNA gene similarity. In batch cultures, Clostridium sp. BS-1 produced 550 ± 31 mL L⁻¹ of H₂, 0.36 ± 0.01 g L⁻¹ of acetic acid, 0.44 ± 0.01 g L⁻¹ of butyric acid, and 0.98 ± 0.03 g L⁻¹ of hexanoic acid in a 4-day cultivation. The production of hexanoic acid increased to 1.22 and 1.73 g L⁻¹ with the addition of 1.5 g L⁻¹ of sodium acetate and 100 mM 2-(N-morpholino)ethanesulfonic acid (MES), respectively. Especially when 1.5 g L⁻¹ of sodium acetate and 100 mM MES were added simultaneously, the production of hexanoic acid increased up to 2.99 g L⁻¹. Without adding sodium acetate, 2.75 g L⁻¹ of hexanoic acid production from D-galactitol was achieved using a coculture of Clostridium sp. BS-1 and one of the isolates, Clostridium sp. BS-7, in the presence of 100 mM MES. In addition, volatile fatty acid (VFA) production by Clostridium sp. BS-1 from D-galactitol and D: -glucose was enhanced when a more reduced culture redox potential (CRP) was applied via addition of Na₂S·9H₂O.

Abstract  One acetamide and 5 acetanilide herbicides are currently registered for use in the United States. Over the past several years, ethanesulfonic acid (ESA) and oxanilic acid (OA) degradation products of these acetanilide/acetamide herbicides have been found in U.S. ground waters and surface waters. Alachlor ESA and other acetanilide degradation products are listed on the U.S. Environmental Protection Agency's (EPA) 1998 Drinking Water Contaminant Candidate List. Consequently, EPA is interested in obtaining national occurrence data for these contaminants in drinking water. EPA currently does not have a method for determining these acetanilide degradation products in drinking water; therefore, a research method is being developed using liquid chromatography/negative ion electrospray/mass spectrometry with solid-phase extraction (SPE). A novel chromatographic separation of the acetochlor/alachlor ESA and OA structural isomers was developed which uses an ammonium acetate-methanol gradient combined with heating the analytical column to 70 degrees C. Twelve acetanilide degradates were extracted by SPE from 100 mL water samples using carbon cartridges with mean recoveries >90% and relative standard deviations < or =16%.

Abstract  Novel covalently crosslinked membranes based on sulfonated poly(ether ether ketone) and carboxylated polysulfone exhibit much lower methanol crossover and better performance in direct methanol fuel cells at 65 °C in 1 and 2 M methanol solutions compared to Nafion 115 membranes.

Abstract  Proton solvation properties and transport mechanisms have been studied in hydrated Nafion using the self-consistent multistate empirical valence bond (SCI-MS-EVB) method that includes the effects excess proton charge defect delocalization and Grotthuss proton hopping. It was found that sulfonate groups influence excess proton solvation, as well as the proton hydration structure, by stabilizing a more Zundel-like (H(5)O(2)(+)) structure in their first solvation shells. Hydrate proton-related hydrogen bond networks were observed to be more stable than networks with water alone. Diffusion rates, Arrhenius activation energies, and transport pathways were calculated and analyzed to characterize the nature of the proton transport. Diffusion rate analysis suggests that a proton-hopping mechanism dominates the proton transport for the studied water loading levels and that there is a clear degree of anticorrelation with the vehicular transport. The activation energy drops quickly with an increasing water content when the water loading level is smaller than ∼10 H(2)O/SO(3)(-), which is consistent with experimental observations. The sulfonate groups were also found to affect the proton hopping directions. The temperature and water content effects on the proton transport pathways were also investigated.

Abstract  We report the development and application of a capillary hollow fibre membrane interface using methanol as an acceptor phase to deliver target analytes to an electrospray ionization source and a triple quadrupole mass spectrometer. Superior fluid handling systems lead to greater signal stability and membrane integrity for the continuous on-line monitoring of polar and charged analytes in complex aqueous samples with detection limits in the parts-per-trillion to parts-per-billion range. The system can be operated in either a continuous flow or a stopped acceptor flow mode - the latter giving rise to greater sensitivity. We report detection limits, enrichment factors and signal response times for selected analytes with polydimethylsiloxane and Nafion® polymer membrane interfaces. In addition, we demonstrate the use of this interface to detect pharmaceuticals and other contaminants in natural water and artificial urine. The improved sensitivity and analytical response times of our CP-MIMS system make it possible to continuously monitor dynamic chemical systems with temporal resolutions on the order of minutes. Presented is a comparison of the performance of CP-MIMS versus direct infusion electrospray ionization, demonstrating the potential advantages over direct infusion for trace analyte measurements in complex, high ionic strength samples. Furthermore, by continuously flowing a reaction mixture in a closed loop over the interface, we demonstrate the use of the system as an in situ reaction-monitoring platform for the chlorination of a model organic compound in aqueous solution.

Abstract  Large-scale energy storage has become the main bottleneck for increasing the percentage of renewable energy in our electricity grids. Redox flow batteries are considered to be among the best options for electricity storage in the megawatt range and large demonstration systems have already been installed. Although the full technological potential of these systems has not been reached yet, currently the main problem hindering more widespread commercialization is the high cost of redox flow batteries. Nafion, as the preferred membrane material, is responsible for about 11% of the overall cost of a 1 MW/8 MWh system. Therefore, in recent years two main membrane related research threads have emerged: 1) chemical and physical modification of Nafion membranes to optimize their properties with regard to vanadium redox flow battery (VRFB) application; and 2) replacement of the Nafion membranes with different, less expensive materials. This review summarizes the underlying basic scientific issues associated with membrane use in VRFBs and presents an overview of membrane-related research approaches aimed at improving the efficiency of VRFBs and making the technology cost-competitive. Promising research strategies and materials are identified and suggestions are provided on how materials issues could be overcome.

Abstract  We describe beta- and gamma-cyclodextrins (beta- and gamma-CD)-modified monolithic columns prepared by sol-gel process and chemical modifications. The monolithic silica column was fabricated inside a fused-silica capillary with 100 microm inner diameter by sol-gel process. The monolithic silica matrix was chemically modified chiral selectors of beta- or gamma-CDs with a spacer of 3-glycidoxypropyltrimethoxysilane by on-column reactions. Gamma-CD-modified monolithic column has successfully been applied for the separation of dansyl amino acid enantiomers. Beta-CD-modified monolithic column has been used for the separation of the positional isomers of o-, m-, and p-cresols and the enantioseparation of racemates of benzoin and several dansyl amino acids by capillary electrochromatography, respectively. For the separation of neutral positional isomers, a positive electric field was applied. However, for the separation of negatively charged analytes, a negative electric field was applied at the inlet of column. The separation efficiency of 5.0 x 10(4) theoretical plates/m for dansyl-L-threonine was obtained at electric field strength of -300 V/cm in the mobile phase of 50 mM 2-(N-morpholino)ethanesulfonic acid (MES)-Tris/methanol (70/30) buffer at pH 7.0. L-enantiomers were eluted as the first peak. Scanning electron micrograph showed that monolithic columns have the morphology of continuous skeleton and large through-pores.

Abstract  The use of several designs of amperometric enzymatic biosensors based on the immobilized tyrosinase enzyme (Tyr) for determining dichlorvos organophosphate pesticide are described. The biosensors are based on the reversible inhibition of the enzyme and the chronocoulometric measurement of the charge due to the charge-transfer mediator 1,2-naphthoquinone-4-sulfonate (NQS). Tyr becomes active when reducing the quinone form of the mediator molecule (NQS) to the reactive o-diol form substrate of Tyr (H(2)NQS) at the working electrode, thus permitting modulation of the catalytic activity of the enzyme and measurement of the inhibition produced by the pesticide. The full activity of the enzyme reversibly recovers after removal of the pesticide and re-oxidation of H(2)NQS. Tyr was immobilized onto electrodes using different procedures: (i) entrapment within electropolymerized conducting and non-conducting polymers, (ii) covalent attachment to self-assembled monolayers (SAM), (iii) cross-linking with glutaraldehyde (and nafion covering) and (iv) dispersion within carbon-paste electrodes. The mediator was co-immobilized onto the working electrode next to the enzyme and reagentless biosensors were subsequently constructed. In the SAM design (ii) NQS was added to the solution. The analytical properties of the different biosensors based on the competitive inhibition produced by dichlorvos were then compared. A detection limit of about 0.06 microM was obtained for dichlorvos with entrapment of NQS and Tyr within electropolymerized poly(o-phenylenediamine) polymer (oPPD), which was the design that proved to have the best analytical performance.

Abstract  The enantioseparation of nine commercially available basic drugs was achieved on polysaccharide-based chiral stationary phases with the acidic additive ethanesulfonic acid and the basic additive butylamine. Seven different commercially available CSPs were used for the study (AD, AS, OD, OJ, OG, OB, and OC). Mobile phase additives have been proven to be essential in obtaining satisfactory enantio-resolution in terms of both efficiency and selectivity. Significantly improved selectivities were obtained for the basic probe drugs with the acidic additive, ethanesulfonic acid, rather than the basic additive, butylamine. This is best seen with Chiralpak AS CSP. No enantioseparation for the nine drugs was observed when butylamine was used as an additive; however, satisfactory enantioseparation for the nine drugs was achieved using ethanesulfonic acid. Higher column efficiencies were observed with the acidic additive, especially when isopropanol was used as a modifier. Higher sensitivity was also achieved with ethanesulfonic acid because of the significantly lower background at the UV detection wavelength. The acidic additive was demonstrated to be superior to the basic additive for the enantioseparation of basic drugs using seven different polysaccharide-based CSPs. These results are counterintuitive to the common "rule of thumb" in enantioseparation that states acidic additives work best for acidic analytes and basic additives work best for basic analytes. The beneficial effects of acidic additive in enantioseparations observed in this study could significantly improve the applicability of polysaccharide-based CSPs for the enantioseparation of basic analytes.

Abstract  Nafion/lead-ruthenate pyrochlore chemically modified electrode (NPyCME) showed a remarkable dual sensing activity toward NO2- oxidation and NO reduction as demonstrated by cyclic voltammetry (CV), ac-impedance spectroscopy and flow injection analysis (FIA). The mechanistic parameters of current function, charge transfer resistance and exchange current for the NPyCME, GCE and Nafion-coated GCE were evaluated and compared. The disproportionation reaction of (NO2-)-O-III into (NO3-)-O-IV + (NO)-O-II in acidic solution was used as a model system for testing the dual sensing ability of the NPyCME. The obtained crossover peak response for NO2- oxidation and NO reduction in pH 1.65 buffer solution gave the direct proof for the applicability of the NPyCME in the dual electrocatalytic action. By flow injection analysis, under optimized conditions, the calibration curve was linear in the range of 100 nM-100 muM and 800 nM-63.3 muM and the detection limit (S/N = 3) was 4.8 nM and 15.6 nM for NO2- and NO, respectively.

Abstract  We have developed a new half-membrane-electrode assembly (MEA)-type cell that allows us to conduct attenuated total reflectance-Fourier transform infrared (ATR-FTIR) measurements at the Pt/Nafion interface under humidified N(2)/O(2) atmosphere. The cell consists of a gas-diffusion type anode placed on a carbon separator with a gas flow field, a Pt film cathode deposited chemically on an Si ATR prism and a Nafion NRE(R)211 electrolyte sandwiched between them. The construction allows the control of the atmosphere at the cathode by those at the anode via the electrolyte of 20-microm thickness. An infrared absorption band was observed at 1400-1403 cm(-1) under humidified oxygen atmosphere in close association with the appearance of ORR current. Its absence under N(2) atmosphere and insensitivity to the change from H(2)O to D(2)O humidification led us to ascribe the band to the O-O vibration of the adsorbed oxygen molecule O(2)(ads). The band intensity increased with increasing ORR current but decreased significantly in the limiting current region. However, the stability of the species at potentials as high as 1.1 V vs. the reversible hydrogen electrode (RHE) led us to rule out the possibility that the band could be due to adsorbed superoxide O(2)(-).

Abstract  A selective and sensitive ion chromatographic method has been developed for the determination of beryllium in a number of water samples at low-microg/l concentrations. The separation was performed on a 250x4.0 mm I.D. iminodiacetic acid functionalised silica gel column. Chromatographed Be(II) was detected using visible detection at 590 nm following post-column reaction with chrome azurol S (CAS). The optimum separation and derivatisation conditions were studied in detail. The optimum eluent conditions were found to be 0.4 M KNO3, adjusted to pH 2.5 using HNO3, with optimum post-column detection being achieved using a solution containing 0.26 mM CAS, 2% Triton X-100, 50 mM 2-(N-morpholino)ethanesulfonic acid, pH 6.0. Under the above conditions, the concentration detection limit for Be(II) was found to be 3 microg/l in a standard solution and 4 microg/l in a typical tap water sample, using a 250 microl injection. The method was linear over the investigated range of 10 microg/l to 10 mg/l and highly reproducible. The method was successfully applied to a number of water samples of varying matrix complexity, including simulated seawater, and also to a natural freshwater certified reference material NIST 1640.

Abstract  The effects of sulfur sources on the desulfurization activity of Rhodococcus erythropolis KA2-5-1 were investigated by using an exponential fed-batch culture technique. The feed rate of a sulfur source was controlled independently of the feed rate of ethanol, which was used as a carbon and energy source. Among the sulfur sources examined were dibenzothiophene (DBT), ammonium sulfate, L-cysteine, L-methionine, and 2-amino-ethanesulfonic acid. When the fed-medium contained DBT as the sole sulfur source, KA2-5-1 cells showed a maximum desulfurization activity of approximately 130 mmol 2-HBP kg-cell(-1) h(-1). Similar levels of enzyme activity were also achieved with inexpensive ammonium sulfate by using the exponential fed-batch culture technique. In addition, higher levels of desulfurization activity were achieved by increasing the dosage of the DBT desulfurization (dsz) operon and dszD gene in R. erythropolis KA2-5-1. The recombinant strain showed a maximum desulfurization activity of approximately 250 mmol 2-HBP kg-cell(-1) h(-1) in the exponential fed-batch cultures.

Abstract  Sepsis is a severe systemic inflammatory response that is associated with high morbidity and mortality. A previous study using an animal model of sepsis showed that survival was significantly lower in WT mice than in P2Y(2) receptor (P2Y(2)R)-deficient mice, suggesting that P2Y(2)R plays a role in septic death. We therefore investigated the role of P2Y(2)R in the inflammatory responses of RAW264.7 murine macrophages to LPS. LPS time-dependently upregulated P2Y(2)R mRNA levels, with a prominent increase observed at 4 h. In addition, LPS increased ATP release in a time dependent manner (5-120 min post LPS treatment). Accordingly, we pretreated cells with LPS for 4 h to induce P2Y(2)R expression and then stimulated the cells with UTP or ATP for 16 h. Interestingly, ATP- or UTP-dependent P2Y(2)R activation in LPS-pretreated cells resulted in dramatically enhanced HMGB1 secretion, COX-2 and iNOS expression, and furthermore PGE2 and NO production compared to LPS treatment alone (4 h) or ATP or UTP treatment alone (16 h), an effect that was inhibited by P2Y(2)R silencing. In addition, these increases in HMGB1 secretion, COX-2 and iNOS expression and PGE(2) and NO production commonly involved the JNK, PKC and PDK pathways. Taken together, these data demonstrate that LPS-dependent upregulation of P2Y(2)R plays a critical role in facilitating the inflammatory responses induced by LPS.

Abstract  Neocortical and striatal TRPV1 (vanilloid or capsaicin) receptors (TRPV1Rs) are excitatory ligand-gated ion channels, and are implicated in psychiatric disorders. However, the purported presynaptic neuromodulator role of TRPV1Rs in glutamatergic, serotonergic or dopaminergic terminals of the rodent forebrain remains little understood. With the help of patch-clamp electrophysiology and neurochemical approaches, we mapped the age-dependence of presynaptic TRPV1R function, and furthermore, we aimed at exploring whether the presence of CB1 cannabinoid receptors (CB1Rs) influences the function of the TRPV1Rs, as both receptor types share endogenous ligands. We found that the major factor which affects presynaptic TRPV1R function is age: by post-natal day 13, the amplitude of capsaicin-induced release of dopamine and glutamate is halved in the rat striatum, and two weeks later, capsaicin already loses its effect. However, TRPV1R receptor function is not enhanced by chemical or genetic ablation of the CB1Rs in dopaminergic, glutamatergic and serotonergic terminals of the mouse brain. Altogether, our data indicate a possible neurodevelopmental role for presynaptic TRPV1Rs in the rodent brain, but we found no cross-talk between TRPV1Rs and CB1Rs in the same nerve terminal.

Abstract  In this work, a highly sensitive and stable sensing scaffold consisting of gold nanoparticle-encapsulated TiO2 nanotubes, the hydrophilic ionic liquid, 1-decyl-3-methylimidazolium bromide, and Nafion was developed for the fabrication of electrochemical enzyme biosensors. A significant aspect of our work is the application of 12-phosphotungstic acid as both a highly localized photoactive reducing agent to deposit well-dispersed gold nanoparticles on TiO2 nanotubes and an electron mediator to accelerate the electron transfer between an enzyme and the electrode. After characterizing the nanocomposite component of the scaffold by Fourier transform infrared spectroscopy, X-ray diffraction and transmission electron microscopy, thiolated horseradish peroxidase (as a model enzyme) was immobilized on the scaffold and the biosensor was applied to the detection of H2O2. The direct electron transfer between the enzyme and the electrode was promoted by the excellent biocompatibility and conductivity of the scaffold. In addition, a thiolated enzyme has significantly improved the stability and direct electron transfer of horseradish peroxidase on the biosensor, which could be ascribed to the strong affinity between the sulfhydryl group on the enzyme and gold nanoparticles on the biosensor surface. Cyclic voltammetry, chronoamperometry, and square wave voltammetry were used to study the electrochemistry and analytical performance of the biosensor. A dynamic range from 65 to 1600 μM, a limit of detection of 5 μM, and a sensitivity of (18.1 ± 0.43) × 10(-3) μA μM(-1) H2O2 were obtained. The sensing scaffold based on the nanocomposite was demonstrated to be effective and promising in developing enzyme biosensors.

Abstract  Glucose oxidase (GOD) was adsorbed into a nanoporous TiO₂ film layered on the surface of an iron phthalocyanine (FePc) vertically-aligned carbon nanotube (CNT) modified electrode. A Nafion film was then dropcast on the electrode's surface to improve operational and storage stabilities of the GOD-based electrode. Scanning electron microscopy (SEM) micrographs revealed the formation of FePc and nanoporous TiO₂ nanoparticles along the sidewall and the tip of CNTs. Cyclic voltammograms of the GOD electrode in neutral PBS exhibited a pair of well-defined redox peaks, attesting the direct electron transfer of GOD (FAD/FADH₂) with the underlying electrode. The potential of glucose electro-oxidation under nitrogen was ∼+0.12 V with an oxidation current density of 65.3 μA cm(-2) at +0.77 V. Voltammetric and amperometric responses were virtually unaffected by oxygen, illustrating an efficient and fast direct electron transfer. The modification of the CNT surface with FePc resulted in a biosensor with remarkable detection sensitivity with an oxygen-independent bioelectrocatalysis. In deaerated PBS, the biosensor displayed average response time of 12 s, linearity from 50 μM to 4 mM, and a detection limit of 30 μM (S/N=3) for glucose.

Abstract  The present study was conducted to assess in rats the comparative effects of a number of chelating agents on the urinary excretion and tissue distribution of A1. Adult male Sprague-Dawley rats received a single intraperitoneal dose of aluminium (A1) nitrate nonahydrate (0.24 mmol/kg). Ten min. after A1 injection 1,2-dimethyl-3-hydroxypyrid-4-one, 2,3-dihydroxybenzoic acid, picolinic acid, methylmalonic acid, ethylenediamine-di(o-hydroxyphenylacetic) acid, 1-benzyl-2-methyl-3-hydroxypyrid-4-one, 1-(p-methylbenzyl)-2-methyl-3-hydroxypyrid-4-one, 1-(p-methoxy-benzyl)-2-methyl-3-hydroxypyrid-4-one, 1-(p-chlorobenzyl)-2-methyl-3-hydroxypyrid-4-one, 1-benzyl-2-ethyl-3-hydroxypyrid-4-one, 1-(p-methyl-benzyl)-2-ethyl-3-hydroxypyrid-4-one, 1-[3-hydroxy-2-methyl-4-oxopyridyl]-2-ethanesulfonic acid and 1-benzyl-(4-carboxylic acid)-3-hydroxy-2-methyl-4-oxopyridine were given by gavage at 1.79 mmol/kg. A control group received similar volumes of distilled water. An additional group of rats received a subcutaneous injection of desferrioxamine at 1.79 mmol/ kg. Urine samples were collected daily for three consecutive days and the animals were killed after this period. Samples of brain, bone, liver, kidney and spleen were collected. Although desferrioxamine, 1,2-dimethyl-3-hydroxypirid-4-one, 1-(p-methylbenzyl)-2-methyl-3-hydroxypyrid-4-one, 1-(p-methoxybenzyl)-2-methyl-3- hydroxypyrid-4-one, 1-(p-methylbenzyl)-2-ethyl-3-hydroxypyrid-4-one, 1-[3-hydroxy-2-methyl-4-oxopyridyl]-2-ethanesulfonic acid and 1-benzyl-(4-carboxylic acid)-3-hydroxy-2-methyl-4-osopyridine significantly enhanced the total excretion of A1 into urine, only treatment with 1-(p-chlorobenzyl)-2-methyl-3-hydroxypyrid-4-one and 1-benzyl-2-ethyl-3-hydroxypyrid-4-one significantly reduced A1 concentrations in all analyzed tissues. No beneficial effects of the remaining chelators on Al mobilization were observed. Further studies on the effects of some 3-hydoxrypyrid-4-ones on A1 removal can be of interest for the treatment of A1 accumulation and toxicity.

Abstract  The applicability of two different types of Nafion membrane dryers (based on counter-current flow and desiccant drying) and of a new ozone scrubbing material, polyphenylene sulphide wool (noXon-S), to adsorptive sampling of selected volatile sulphur compounds (methanethiol, dimethyl sulphide, isopropanethiol and isobutanethiol) is investigated at the low ppb (v/v) level (1-5 ppb). No analyte losses occur with either type of dryer at relative humidities (RH) of < or = 50%, while at higher RH values particularly the thiols tend to be lost (between 6 and 32%) even after conditioning. The actual losses depend more on the state of the individual permeation membrane rather than on the type of dryer. NoXon-S is a highly suitable ozone scrubber material for sulphur compounds since it efficiently removes ozone without retainment of the analytes and without the formation of blanks or artefacts from the scrubber material. The combined use of a Nafion membrane dryer and a noXon-S ozone scrubber is thus recommended for artifact-free sampling of sulphur compounds.

Abstract  A new portable instrument has been developed that offers rapid detection of ozone at the parts per billion (ppb) level for personal exposure monitoring. The personal ozone monitor is based on the EPA Federal Reference Method of UV absorbance and has the advantage of being small (10 cm x 7.6 cm x 3.8 cm), lightweight (0.3 kg), low power (2.9 W), and battery-operated. The instrument can be worn by an individual during normal daily activities because it is unaffected by humidity, physical orientation, temperature, and vibration. In order to eliminate any significant interference from water vapor, Nafion tubing was installed before the detection cell, and the optical path was lined with quartz. A precision of 1.5 parts per billion by volume (ppbv) and limit of detection of 4.5 ppbv (S/N = 3) was demonstrated with the instrument making measurements every 10 s.

Abstract  Micellar electrokinetic chromatography (MEKC) was applied to the separation of a group of N-phenylpyrazole derivatives. Sodium dodecyl sulfate (SDS) as micellar system and 2-(N-cyclohexylamino)ethanesulfonic acid (CHES) as separation buffer (pH 10) were employed in the absence and presence of different percentages of medium chain alcohols (n-propanol or n-butanol). The separation of multicomponent mixtures of the solutes studied enabled the rapid determination of their retention factors which, in turn, allowed the study of the separation selectivity of compounds and the determination of their solute-micelle association constants (from the linear variation of the retention factors as a function of the total surfactant concentration in the separation buffer). Separation selectivity was studied according to the elution range and number of solutes separated in all the electrolyte solutions employed (45 micellar phases). The effect of the buffer concentration (0.05, 0.08 and 0.10 M), the alcohol nature (n-propanol or n-butanol) and the alcohol percentage (1, 3 or 5%) of the values obtained for the solute-micelle association constants was also studied. The best separation (12 solutes) was performed when a 0.08 M CHES buffer, pH 10, 0.02 M SDS modified by 5% n-butanol was used. The possibilities of using MEKC for evaluating the hydrophobicity of compounds was investigated through the study of the correlation between the logarithm of the retention factors of N-phenylpyrazole derivatives and their logarithm of the octanol-water distribution coefficients estimated by high performance liquid chromatography (HPLC).

Abstract  Uniformly sized microspheres tangled with cup-stacked carbon nanofibers (CSCNFs) were directly synthesized by the pyrolysis of poly(ethylene glycol) (PEG) with a nickel catalyst. A PEG/Ni membrane was prepared on a silicon wafer surface by heating it to 750 °C at a heating rate of 15 °C min(-1). The wafer was heated to a temperature of 400 °C and was held at that temperature for 1 h before raising the temperature to 750 °C for 10 min to form the CSCNF microspheres. The final CSCNF microspheres and the intermediates were evaluated using scanning electron microscopy, transmission electron microscopy, X-ray diffractometry, and Raman spectroscopy to elucidate the growth mechanism. Furthermore, the CSCNF microspheres were successfully dispersed and maintained their spherical shape in an aqueous solution containing 0.5% Nafion. The CSCNF microspheres have the potential to work as a sophisticated carrier with high adsorption and fast electron-transfer exchange properties based on the graphene edges of the nanofiber surface.

Abstract  A sensitive capillary electrophoretic method was developed for the determination of thiodiglycolic acid (TDA) in urine which avoids the pretreatment of the urine sample. Several carrier electrolytes were examined. The most suitable carrier electrolyte system consisted of potassium hydrogen phthalate (5 mM), 2-(N-morpholino)ethanesulfonic acid (50 mM) and tetradecyltrimethylammonium bromide (0.5 mM), pH 5.2. Ten times diluted fresh midstream void urine was used for the determination. In this way, the concentrations of TDA between 5 and 50 mg/l in undiluted urine samples can be determined.

Abstract  This paper reports on validation experiments with the recently developed microAeth (R), a pocket-sized device which is able to obtain real-time and personal measurements of black carbon (BC) aerosol. High reproducibility was observed when comparing the results from six new individual units during fixed-site monitoring out of a window (relative standard deviation [RSD] = 8% +/- 5%, N = 1442). The results obtained from the microAeth devices agreed with those obtained from a full size rack mounted Aethalometer, based on both the 1-minute data (R = 0.92, slope = 1.01 +/- 0.01, N = 1380) and 24-h average data. The 24-h average of real time data obtained from the microAeths was comparable to the BC concentration obtained from 24-h integrated PM2.5 filter deposits, as determined by multi-wavelength optical absorption (R = 0.98, slope = 0.92 +/- 0.07, N = 12). Rapid environmental changes in relative humidity (RH) and temperature (T) can result in false positive and negative peaks in the real time BC concentrations, though averages > 1-2-hour are only minimally affected. An inlet with a diffusion drier based on Nafion (R) tubing was developed in order to use BC data with a high time resolution. The data shows that the diffusion drier greatly reduce the impacts from rapid changes in RH and T when the monitoring system is worn in close proximity to the body (e. g., in the vest pocket).

Abstract  In this paper, we present two new methodologies of improving the performance of microchip-based electrochemical detection in microfluidic devices. The first part describes the fabrication and characterization of epoxy-embedded gold microelectrode arrays that are evenly spaced and easily modified. Electrodepositions using a gold plating solution can be performed on the electrodes to result in a 3D pillar array that, when used with microchip-based flow injection analysis, leads to an eightfold increase in signal (when compared to a single electrode), with the LOD for catechol being 4 nM. For detecting analytically challenging molecules such as nitric oxide (NO), platinization of electrodes is commonly used to increase the sensitivity. It is shown here that microchip devices containing either the pillar arrays or more traditional glassy carbon electrodes can be modified with platinum black (Pt-black) for NO detection. In the case of using glassy carbon electrodes for NO detection, integration of the resulting platinized electrode with microchip-based flow analysis resulted in a ten times signal increase relative to use of a bare glassy carbon electrode. In addition, it is demonstrated that these electrodes can be coated with Nafion to impart selectivity toward NO over interfering species such as nitrite. The LOD for NO when using the Pt-black /Nafion-coated glassy carbon electrode was 9 nM. These electrodes can also be embedded in a polystyrene substrate, with the applicability of these sensitive and selective electrodes being demonstrated by monitoring the adenosine triphosphate-mediated release of NO from endothelial cells immobilized in a microfluidic network without any adhesion factor.